{"product_id":"replacement-tail-kit-for-spearwerx-ghost-450g","title":"Replacement Tail Kit for SPEARWERX Ghost 450g","description":"\u003cp\u003e\u003cstrong\u003eReplacement Tail Section for Ghost 450-gram Javelins.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eGhost Javelins made in 2026 and after, are designed to have the tail section replaced if needed.\u003c\/p\u003e\n\u003cp\u003eGhost Javelins made prior to 2026 can be replaced, if the tail section has come loose and can be removed.\u003c\/p\u003e\n\u003cp\u003eThis Kit Includes:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eNew Tail Section\u003c\/li\u003e\n\u003cli\u003e3\/32 Drill Bit\u003c\/li\u003e\n\u003cli\u003e.050 Allen Hex Wrench\u003c\/li\u003e\n\u003cli\u003eSet Screws\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eYou will need (not supplied)\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eLow Speed Drill\u003c\/li\u003e\n\u003cli\u003eMasking Tape\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eTo replace the tail section, follow these steps:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFor New Models\u003c\/strong\u003e, use a .050 Hex Allen Wrench to remove the 2 set screws holding the tail in place. remove the tail.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFor Old Models\u003c\/strong\u003e, pull the tail section out.\u003c\/li\u003e\n\u003cli\u003ePlace the removed tail on a scale and weigh the tail in grams.\u003c\/li\u003e\n\u003cli\u003eOrder the Replacement Tail kit for SPEARWERX Ghost 450g\u003c\/li\u003e\n\u003cli style=\"font-weight: bold;\"\u003e\u003cstrong\u003eEmail the weight of the tail in grams, taken in the above steps to customerservice@spearwerx.com\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eWhen your kit arrives:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eYour kit will include- \u003cem\u003eThe Replacement Tail, a .050 Allen Hex Wrench, 3\/32 Inch Drill Bit, New Set Screws\u003c\/em\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFor 2026 and newer models -\u003c\/strong\u003e\n\u003cul\u003e\n\u003cli\u003eSlide the new tail into the javelin so that it rests fully into the shaft\u003c\/li\u003e\n\u003cli\u003eIf the tail is too tight, remove a small amount of masking tape that is wrapped on the tail section. \u003c\/li\u003e\n\u003cli\u003eif the tail is too loose, you can add a small amount of masking tape to the insertable section of the tail to form a snug fit (tape not included)\u003c\/li\u003e\n\u003cli\u003eUse the 3\/32 drill bit to drill through the existing hole in the shaft and into the new tail deep enough to just penetrate the tail.\u003c\/li\u003e\n\u003cli\u003eUse the included .050 Allen hex wrench and insert the set screw into the hole.\u003c\/li\u003e\n\u003cli\u003eTurned Clockwise until the set screw is just below the surface on the shaft\u003c\/li\u003e\n\u003cli\u003eRepeat process on other side of the shaft.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFor pre 2026 Models\u003c\/strong\u003e\n\u003cul\u003e\n\u003cli\u003eSlide the new tail into the javelin so that it rests fully into the shaft\u003c\/li\u003e\n\u003cli\u003eIf the tail is too tight, remove a small amount of masking tape that is wrapped on the tail section. \u003c\/li\u003e\n\u003cli\u003eif the tail is too loose, you can add a small amount of masking tape to the insertable section of the tail to form a snug fit (tape not included)\u003c\/li\u003e\n\u003cli\u003ePlace a piece of masking tape around the javelin shaft near the end where the tail is inserted. This piece of tape is used to prevent the drill bit from sliding.\u003c\/li\u003e\n\u003cli\u003eUse the 3\/32 drill bit to drill through the shaft and new tail piece to create a hole for the set screw. Only about 1\/4-inch depth is needed. Hold the drill steady and perpendicular to the shaft. Drill Slow, not much force is needed.\u003c\/li\u003e\n\u003cli\u003eUse the included .050 Allen hex wrench and insert the set screw into the hole.\u003c\/li\u003e\n\u003cli\u003eTurned Clockwise until the set screw is just below the surface on the shaft\u003c\/li\u003e\n\u003cli\u003eRepeat process on other side of the shaft.\u003c\/li\u003e\n\u003cli\u003eRemove the tape from the rear portion of the shaft and make sure the set screws are just below the surface of the shaft\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"SPEARWERX LLC","offers":[{"title":"Default Title","offer_id":46901117812887,"sku":null,"price":75.0,"currency_code":"AED","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0733\/0091\/files\/tail.png?v=1770660219","url":"https:\/\/shop.spearwerx.com\/products\/replacement-tail-kit-for-spearwerx-ghost-450g","provider":"SPEARWERX LLC","version":"1.0","type":"link"}